|
» Generated Results for air tools
4/1/03
The tool carriage delivers the compressed air to the tools on the floor of store
00:00 - W4-airsolution eliminates the undesirable forces from spring, the voyage or the length available of the working station does not reduce, and incorporates the principal line of air via 2 integrated Po pipe. Préinstallé with intervals of 6 pi of the valves at Po ball are given for the air of tapping and have exits connected to the carriages with the pipe polyurethane. The pipe is encapsulated in the chain of guidance of energy out of plastic, which is internally guided in the aluminium profile.
The innovating product of systems of transport of Wampfler the effective provisioning of supply compressed with the tools on assembly lines is not as easy as one would think. While small products can be assembled with tool-movements limited to a surface from 2 to 3 square feet, larger products such as apparatuses, cars or even the mobile equipment of ground require workmen to move around the product during the assembly. In certain cases, the workman is also requested with walk beside the product while it moves along a belt of assembly. The tools which are connected by the pipes in spiral to the static points require a rack or a plate power station for storage. Consequently, of the workmen are forced to move again with the rack with the change or to replace the little or the casings, or with the tools for exchange. The place of work can also include the pipes of dragged. which increase risks of release, and thus, the staff safety and the effectiveness of place of work the Tool-rails with the mobile carriages parallel with the belts of assembly increase the effectiveness considerably. Tools are suspended of a compensator or a retractor of spring which is then connected to the carriage. The carriage can be easily shifted at the place required exact over a length of working station of to 60 feet, allowing the mobility of workman along the assembly line. Moreover, while the mobile carriage can adapt to more than one tool, the operators can exchange tools very quickly. Typically, the connection of air between the static point of air intake and the mobile carriage are achieved by the festooned pipes. Where festooned of the pipes are used, because the pipe carriages function in the same rail as the tool carriage, for the storage of pipe, the length of voyage is tiny room from 10 to 15%. The alternative is the use of the pipes in spiral which are guided on a steel wire parallel with the rail of tool. Where pipes in spiral are used, the length of voyage is also reduced. Moreover, the forces of spring produced by the pipes in spiral require that carriages be equipped with a brake to remain in position required. Such connections of air, if using the festooned pipes or in spiral, suffer from the fall of significant pressure in the system and can make necessary of the additional pipes of air and/or an increase to the pressure of system. W4-airsolution. again produced from Wampfler.s entirely eliminates the undesirable forces from spring, the voyage or the length available of the working station does not reduce, and incorporates the principal line of air by the intermediary of an integrated pipe 2., reducing the atmospheric loss of pressure significantly. The rail of tool and the line of air are combined in a simple aluminium extrusion, the integrated pipe of air can be fed with one or the two ends of the system and valves with ball to type the air are préinstallées with intervals of 6ft. The exits of valve with ball are connected to the carriages with a polyurethane pipe. The pipe is encapsulated in a chain of guidance of energy out of plastic, which is internally guided in the aluminium profile. This innovating arrangement takes account of the very short pipes (C-with-D. no to develop in spirals required) and, thus has as consequence the very high output (as the fall of pressure increases the finite length). The system is modular in the design and bus all the parts are prefabricated, the installation is simple and fast. Consequently, the assembly can be refourbie and turned over to the production in possible section of time the shortest. Application: The compressed offer of air and the electric provisioning for retroact of the tools on an assembly line of fuselage of truck. Two carriages must be independently mobile above the full assembly line length. A number of assembly lines: 2 lines - length of each line: 86 feet - quantity of carriages by the line: 2 directives of customer: Two tools with the need for control units to be divided on 8 working stations without interfering the equipment fixed on the existing ground. Directive of supplier of unit of tools and order: The control unit must be fed in air without interruption; the circulation of air should not be stopped while the carriage moves. Solution De Wampfler: System of W4-airsolution with two carriages, each carriage with tool equipped with a reinforcement of support of tool. Retroact the tools can be stored on the support of tool, control unit can be attached to the reinforcement of carrier. System equipped with. the cable of A.W.G. pipes of air and 5 of driver 14. Time of installation on the site: 2 fitters, each 8 hours (16 hour-man total) for two (2) assembly lines (combination 172 pi), including connection to exist compressed the air and with the power supply. Contacts: Sales: Telephone of the United States De Responsable for the sales Of Wolfgang Brehm: 859-814-2087 FAX: 859-814-2110
Company Information:
Wampfler Inc.
8091 Production Ave., Florence, KY, 41042 USA
Phone: 800-326-2899 FAX: 859-814-2110
http://www.wampfler.com
Select another language:
English Air Tools -
French Air Tools -
German Air Tools -
Italian Air Tools -
Spanish Air Tools
|
|
|
|
» Related categories
» Information Sources
» User comments * BETA *
Currently only available for beta testers, to become a beta tester use our contact form.
|
|
